Flows

Question 1

FO Transit Scan -
List the initial 5 Items
The checklist finishes with
- Glare shield set up for departure
- Pull GRND OP TEST SW MWS(Master Warning System)
- Check trim operation on control column
- FDR
- Oxygen
- Radio Aids Set Up
- Take off data
- Instrument panel set up
- RNAV
- Fuel

Answer 1

• Circuit Breakers
• Lights
• Aircon settings and RAM Airshut
• Cabin fan on
• Pressurisation controller set

Question 2

What is the FO Transit Scan?

Answer 2

• Circuit Breakers
• Lights
• Aircon settings and RAM Airshut
• Cabin fan on
• Pressurisation controller set
• Glare shield set up for departure
• Pull GRND OP TEST SW MWS(Master Warning System)
• Check trim operation on control column
• FDR
• Oxygen
• Radio Aids Set Up
• Aileron, Elevator Trim
• Take off data
• Instrument panel set up
• RNAV
• Fuel

Question 3

Starting with selecting flap to the required setting for take-off what are the other 4 items for the FO taxi scan?

Answer 3

Radar Standby
Flight director on GA if PF
IVSI - Mode full time
Flight controls check elevator/aileron

Question 4

FO Transit Scan -
List the missing Items
The checklist starts with
- Circuit Breakers
- Lights
- Aircon settings and RAM Airshut
- Cabin fan on
- Pressurisation controller set

Answer 4

• Glare shield set up for departure
• Pull GRND OP TEST SW MWS(Master Warning System)
• Check trim operation on control column
• FDR
• Oxygen test / pressure
• Radio / radio Aids Set Up
• Aileron and Elevator Trim
• Take off data
• Instrument panel set up
• RNAV
• Fuel

Question 5

What are the two parts of the - Load sheet arrival / starting flow?

Answer 5

• Radios
• Pushtest MWS
• Pull GRND OP SW, Push in
• Data Card, Record info

Starting
- Beacon on
- TCAS on
- Air Supply off

Question 6

What are the - During Taxi FO scans?

Answer 6

• Flap to required setting for T/O
• Radar to Standby
• Flight Director on GA if PF
• IVSI mode full time
• Flight controls, check Elevator / Aileron

Question 7

What are the FO scans - Runway Entry?

Answer 7

• Strobe ON
• Config Check

Question 8

What are FO scans for - After Take Off Set Climb Power

Answer 8

When the PNF Calls Zero set (on flap retraction)
- PF will call set Climb Power
- PNF - Select SYNC on TMS (guard thrust levers)
- Engine Air On
- APU air off
- APU stop
- AC Pump Off
- Then reset climb power (normally about 88%, or 820 TGT)

Question 9

What are FO scans for - Transition?

Answer 9

• Altimeter 1013.2
• Set altimeter bug to 0
• Set 1st and 2nd airspeed bugs togethor with VFTO bug
• External / logo light off
• Num 2 radio 121.5

Question 10

What are FO scans for - Descent / Transition?

Answer 10

Descent
- Fuel check
- Pressurisation set
- Attitude Alert, Clearnace received
- TCAS down
- Radios set

Transition
- Altimeters to QNH
- Lights

Question 11

What are FO scans for -After Landing?

Answer 11

• Flaps 0
• Trims set (5, or 3.5 up)
• TMS standby / off
• Radar off
• AC pump off
• APU start if required (including APU gen switch)
• Engine anti ice off
• Heaters, Ice detectors
• Air supply, as required
• Pack, as required
• Strobe - off on RWY Exit
• Cancel SAR, if required

Question 12

What are FO scans for - After Shut down

Answer 12

• TCAS STBY
• Beacon Off
• Exterior lights, as required
• EFIS, dim or dim/off

Question 13

What are the FO responses to “Call the Card?”

Captain - “Copied the info, Call the card”

FO

Captain - “Checked”

FO

Captain - “Set and cross checked”

FO

Captain - “Checked”

FO

Answer 13

Captain - “Copied the info, Call the card”

FO - “36 ton card, V1 VR, 109, 113”

Captain - “Checked”

FO - “V2 121”

Captain - “Set and cross checked”

FO - “VFTO, Ver, 160, 170”

Captain - “Checked”

FO - “Flexing at 36 in the Tref window, 88 my side, 93 across the top”

Question 14

What are the FO scans for After Start?

Answer 14

• Airsupply, Packs & APU Air ON “Packs 1 and 2 on, APU air on”
• Monitor engines for bog down (while captain gets gens online)
• Heaters on
• Ice detector on
• Aircon on
• MWS check

Question 15

What is the verbal que to start the after T/O flow?

Answer 15

PM - “Flap 0”
PF - “Set climb power”

Question 16

What is the cue to start the after landing flow?

Answer 16

Captain calls - “Airbrake in”

Question 17

What acronym can be used for the before-start flow?

Answer 17

B FRESH PATSY

B - Beacon on
Fresh - Cabin Air to fresh
P - Packs off
A - APU off
T - Transponder on

Question 18

What acronym can be used for the after start flow?

Answer 18

A HI RPM

A - APU Air On
HI - Heaters & Ice detector on
R - Recirc Cabin Air
P - Packs On
M - MWS check

Question 19

Before the transit scan what is the order of items to be completed?

Answer 19

Triplog

• fuel remaining
• fuel burn
• on blocks and landing time
• landing weight (night column)
• day / night landing

then

Transit scan including setting
- Aircon to auto
- Airspeed bugs together
- Alt bug Accel altitude
- Data recorder is: MM, DD, Sector Num., last 3 didgets of flight number
- Oxygen includes mask intercom check
- After trip go flight plan
- then TOLD card
- instruments checked
- then check route of flight plan
- then clearance

Question 20

When calling the card, when is the top heading read off of aerodata?

Answer 20

• standing start
• eng anti ice on for departure

Otherwise start at flaps

Question 21

What does the FO do once the load sheet is complete?

Answer 21

MWS Red Button - In