*Anesthesia Concepts 2 > Ventilators > Flashcards

Ventilators Flashcards

(38 cards)

Study These Flashcards
1
Q

What type of pressure do ventilators use?

A

positive pressure

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

What are the 4 phases of one cycle in ventilation?

A
  1. inspiration
  2. transition from insp to exp
  3. expiration
  4. transition from exp to insp
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Which phase is most important? Why?

A

inspiration (is active)

expiration is passive

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Does an anesthesia ventilator have rebreathing?

A

Yes. (ICU vents do not rebreathe)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

How are vents classified mainly? (phase)

A

inspiratory phase and how they cycle

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

What are 3 different types of vent inspiratory features?

Describe them.

A
  1. constant flow
  2. non constant flow
  3. constant pressure generators
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

What is constant flow delivery?
How does a high pressure gas source affect insp flow?
How does a low pressure gas source affect insp flow?

A
  • constant flow regardless of circuit a/w pressure
  • high pressure gas (5-50 PSI) allows insp flow to be constant despite a/w resistance
  • low pressure gas (venturi) - varies with a/w pressure
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

What is non constant flow delivery?

A

-flow varies with each insp cycle

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

What is constant pressure generators delivery?

A

delivers constant pressure throughout insp (regardless of gas flow); gas flow will stop when a/w pressure = set ins pressure

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

What is time cycled?

How does this affect TV?

A

-Time is set for duration of inspiration and expiration
(I:E ratio)
-TV is dependent on the set insp time and insp flow

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

What is volume cycled?
What does this prevent against?
Does the patient always receive all of the TV?

A
  • TV is set (insp can be limited by this)
  • Barotrauma
  • TV is always lost due to compliance of system (4-5 cc)
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

What is pressure cycled?

A

pressure is set

tv and insp time may vary

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

What is flow cycled?

A

-Has pressure and flow sensors that allow vent to monitor insp flow at set insp pressure

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

What are the 3 power sources for vents?

A
  • most commonly bellows (uses gas and electricity)
  • compressed gas (gas only)
  • piston (electricity only)
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

What are 2 options to drive a vent?

A
  1. double circuit - bellows compress by gas and pneumatic drive
  2. piston - bellows compress by electricity
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

What phase drives bellows?

17
Q

What do most of our vents have for
cycle
power
set limit

Study These Flashcards
A

most of our vents are
time cycled
electronic control
with volume limit

18
Q

What are the 4 parameters for ventilators in delivery gas?

Study These Flashcards
A
  1. time
  2. volume
  3. pressure
  4. flow rate
19
Q

Describe each parameter.

  1. time
  2. volume
  3. pressure
  4. flow rate
Study These Flashcards
A
  1. I:E ratio, in SECONDS (always) = # of resp cycles in time (i.e. RR)
  2. TV of gas from vent to pt , in mls or liters (MV = L)
  3. impedance from breathing circuit or pts airway due to a/w resistance or lung-thorax compliance [obesity], in cmH2O, mmHg, or kPa
  4. volume of gas to pt over time , L/sec or L/min
    * machine sets flow rate to meet settings?*
20
Q

What separates driving gas from pt gas circuit?

21
Q

What happens to the bellows and ventilator relief valve on inspiration?

Study These Flashcards
A

driving gas enters chamber and increases pressure which causes:
1. ventilator relief valve to close - no gas escapes and all goes to pt
2. bellows are compressed, gas WITHIN bellows is delivered to patient
(gas IN bellows goes to pt, gas outside of bellows (in chamber) does NOT)

22
Q

What happens to the bellows and ventilator relief valve on expiration?

Study These Flashcards
A
  • driving gas exits bellow chamber, pressure drops which causes ventilator relief valve to open
  • exhaled gas fills bellows before any scavenging occurs bc ball (of ventilator relief valve) produces a 2-3 cm H2O back pressure
23
Q

When does gas go to scavenging?

Study These Flashcards
A

On expiration only AFTER bellows are full of exhaled gas

24
Q

How do you determine a tidal volume setting?

25
What is a normal RR setting? | What is a normal I:E ratio?
8-12 bpm | 1:2
26
How do you calculate flow rate?
4-6 x MV | MV = TV x RR
27
How do you calculate TI (time of inspiration)?
TI = TV/flow rate (x 60 sec if in minutes) i.e. flow = 30L/min, RR = 12, TV = 500 ml 500/30000 = 0.0167 x 60 seconds = 1 seconds
28
How do you calculate TE (time of expiration)?
RR/60 seconds = total time - TI if RR is 12 then 12/60 seconds = 1 breath per 5 seconds 5 seconds = total time of I + E then 5 seconds -1 second (insp) = 4 seconds in exp
29
What does the inspiratory pause/sigh feature do? What happens to gas flow? What is the result?
- increases inhalation time by 25% - gas flow stops but gas pressure in bellows is same - result = total volume of gas is held in pts lung until exp
30
What is the calculation for O2 delivery?
CO x O2 content
31
What is the calculation for O2 content?
(hgb x O2sat x 1.39 mlO2) + (PaO2 x .0031 mlO2) *PO2 of 100 mmHg = 0.3 ml of O2/100 ml* (hgb bound O2 + dissolved O2)
32
How do you calculate PaO2 (arterial concentration of O2)
FiO2 - PaCO2/R ``` FiO2 = (Pb - PH2O) = 713 R = 0.8 F = neglible = 0 ```
33
What happens to PaO2 when you increase FiO2 by 10%?
PaO2 increases by 50 mmHg increase FiO2 = increase SaO2 i.e. PaO2 of 100 = FiO2 of 21% inc by 10% = PaO2 of 150 = FiO2 of 30%
34
Describe the following alarms of the ventilator: 1. low pressure alarm 2. sub atm pressure alarm 3. sustained/continuing pressure alarm 4. high peak a/w pressure alarm 5. low O2 supply alarm 6. vent setting alarm
1. detects drop in peak circuit pressure (disconnect) 2. if pressure 10 secs 4. detects excess pressure over 60 cm H2O unless set diff by clinician 5. 6. vent can't deliver set MV
35
What are 3 important monitors on the ventilator?
ETCO2 - detects disconnect O2 analyzer - most important, calibrate at 21% O2 Respirometer VIGILANCE!!!!!!
36
What does the respirometer do? | Where is it located?
- has sensors to detect TV throughout ventilation - alarms if flow reverses toward pt - cartridge is always on exp limb
37
How do you determined EXHALED tv?
TV set on vent + FGF tv - TV lost in system
38
What is different in an ICU vent (vs anesthesia vent)?
1. more powerful (pressure, volume, etc) 2. no CO2 absorber (each breath is fresh) 3. more vent modes 4. gas from vent all goes to pt (vs anesthesia and bellows) 5. no bellows in ICU
*Anesthesia Concepts 2
flashcards
Decks in class (6)
# Cards
Brainscape helps you reach your goals faster, through stronger study habits.
© 2026 Bold Learning Solutions. Terms and Conditions