CTS-D > 1.5 Audio Principles > Flashcards

1.5 Audio Principles Flashcards

(60 cards)

Study These Flashcards
1
Q

Logarithms

A

A logarithm of a number is how many times the number 1Omust be multiplied by itself to get a certain value. For example, the log of 10,000 is
4 and the log of 0.0001 is -4.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
2
Q

Decibel

A

Decibel (dB) describes a base-ten logarithmic relationship of a power ratio between two numbers .

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
3
Q

Decibel Formula for Power

A

dB= 10 * log (P 1 IP,)
Where:
• dB= The change in decibels
• P 1 = The new or measured power measurement
• P, = The original or reference power measurement

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
4
Q

Decibel Formula for Distance

A

dB= 20 *log (01 I D2)
Where:
• dB= The change in decibels
• 0 1 = The original or reference distance
• D 2 =The new or measured distance

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
5
Q

Decibel Formula for Voltage

A

dB = 20 * log ( V 1 I V,)
Where :
• dB= The change i n decibels
• V 1 = The new or measured voltage
• V, = The original or reference voltage

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
6
Q

1Oand 20 Log Formulas

A

In AV, the “10 log” formula is for power calculations only. The “20 log” formula is for voltage, pressure, and distance calculations. Just remember: 1O for power, 20 for everything else.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
7
Q

Reference Level (Decibels)

A
  • OdB SPL = 0.00002 Pa
  • 0 dBV = 1 V
  • 0 dBu = 0.775 V
  • OdBW= 1 W
  • O dBm = 0.001 mW
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
8
Q

Sound pressure level should always fall between

A

O and 140 dB SPL

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
9
Q

Microphone level, which is typically measured in dBu, should be

A

60

to-50 dBu, well below the zero reference of 0.775 volts for the dBu.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
10
Q

Line level on the other hand, should be between

A

O and +4 dBu for pro

audio.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
11
Q

Consumer audio level is

A

-10 dBV (0.316 V)

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
12
Q

SPL (Sound Pressure Level)

A

Sound pressure level (SPL} is a measurement of all the
acoustic energy present in an environment. It is typically
expressed in decibels (dB SPL) .

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
13
Q

SPL Meter Classes

A

0- lab reference standard

1- engineering-grade accuracy

2- is for general purpose

3- intended for noise surveys

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
14
Q

A Weighting ( dB SPL A wtd)

A

hearing conservation and noise ordinance enforcement.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
15
Q

C Weighting ( dB SPL C wtd)

A

More uniform response over the entire frequency

range.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
16
Q

Flat Weighting

A

no filtering. Sometimes referred to as Z (zero) weighting.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
17
Q

loudspeaker polar

pattern directivity

A

how much area

each of your selected loudspeakers will cover

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
18
Q

Loudspeaker Coverage Area Formula

A

D = 2 * (H - h) *tan (CL I 2)
Where:
• D is the diameter of the coverage area I
• H is the ceiling height I
• h is the height of the listeners’ ears
• CL is the loudspeaker’s angle of coverage in dergees

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
19
Q

Current and Voltage ( Ohm’s Law)

A 
I= VI R   I
 Where:  l
 •   I=   Current  I
 •   V=   Voltage
 •   R=   Resistance
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
20
Q

Ohms Law

A

https://s3.amazonaws.com/classconnection/958/flashcards/4268958/jpg/ohms-watts_law-151135DE4FB18BA0551.jpg

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
21
Q

Sensitivity Specification

A

Sens iti vity specifications are a way to determine a
device’s ability to convert one form of energy into
another form of energy . It is used to define the device’s efficiency in converting from one form to another.

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
22
Q

Constant Voltage

A
  1. Constant voltage (25V, 70V , 1OOV) is a method of
    distributing power to loudspeakers over a large area
    with less loss than a typical connection would provide . This can also be called a “high impedance system.”

2 . Also called a high-impedance system, this is a
method of distribution over a large area with less loss
than a typical connection would provide ,

How well did you know this?
1
Not at all
2
3
4
5
Perfectly
23
Q

Specifying a Power Amplifier for

Direct Connection Audio

A
  1. Determine SPL level at the listener
  2. Add 1OdB for voice or 20 dB for music
  3. Find loss over distance in dB (loudspeaker to listener)
  4. Determine power (watts) required at the loudspeaker using the EPR
    formula
  5. Round the result up to an amplifier value that can be readily
    purchased
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
24
Q

Specifying a Power Amplifier for

Distributed Audio

A
  1. Determine SPL level at the listener
  2. Add 1OdB for voice or 20 dB for music
  3. Find loss over distance in dB
  4. Determine watts required at the loudspeaker
  5. Select appropriate tap value for loudspeaker
  6. Repeat steps 1-5 for each loudspeaker
  7. Sum the tap settings from all loudspeakers
  8. Increase the total tap settings by a factor of 1.5
  9. Round the result up to an amplifier value that can be readily purchased
How well did you know this?
1
Not at all
2
3
4
5
Perfectly
25
Lavalier Microphone
Lavalier is a small microphone designed to be worn | either around the neck or clipped to apparel.
26
Boundary microphones
are mounted directly against a hard surface, such | as a conference table, wall, or ceiling.
27
Omnidirectional
Sound pickup is uniform in all directions.
28
Supercardioid
Provides better directionality than the hypercardioid. It has less rear pickup than the hypercardioid
29
Hypercardioid
Is a variant of the cardioid. More directional than the regular cardioid because it rejects more sound from the side. The tradeoff is that some sound will be picked up directly at the rear of the microphone.
30
Cardioid
Pickup is from the front of the microphone only (one direction) in a cardioid pattern. It rejects sounds coming from the side but the most rejection is at the rear of the microphone. The term cardioid refers to the heart shaped polar plot.
31
Bi-directional
Pickup is equal in opposite directions with little or no pickup from the sides. This is sometimes also referred to as a ''figure -eighf' pattern, referring to the shape of its polar plot.
32
Polar Plot
A polar plot is a graphical representation of the relationship between a device's directionality and its output.
33
Frequency Response
Frequency response is a shortened way of expressing a device's amplitude response versus frequency characteristic . A frequency response is usually presented as a graph or plot of a device's output on the vertical axis versus the frequency on the horizontal axis .
34
Dynamic Microphone
A dynamic microphone is a pressure-sensitive microphone of moving coil design that transduces sound into electricity using electromagnetic principles .
35
Condenser Microphone
A condenser microphone transduces sound into | electricity using electrostatic principles.
36
Phantom Power
Phantom power is a direct current (DC) power source available in various voltages
37
Electret Microphone
An electret microphone is a type of condenser microphone. It has prepolarized material. called "electret, n which is applied to the icrophone's diaphragm or backplate . This provides a permanent, fixed charge for one side of the capacitor configuration. This permanent charge eliminates the need for the higher voltage required for powering the typical condenser microphone, so it can be powered using small batteries and normal phantom power .
38
Mic Level
Mic level is a very low level signal. It is only a few | millivolts of electrical energy.
39
Preamplifier
A microphone preamplifier , also known as a mic pre , amplifies a microphone level signal to line level for routing and processing .
40
Line Level
Line level is the strength of an audio signal. Line level 1s used for all routing and processing between components.
41
Line level in a professional audio
1.23 volts, +4 dBu
42
Line Level in Consumer audio
0.316 volts (-10 dBV)
43
Mic Level Voltage
0.001 - 0.003 volts (-60 to -50 dBu)
44
Sensitivity Specification
Sensitivity specifications are a way to determine a device's ability to convert one form of energy into another form of energy . It is used to define the device's efficiency in converting from one form to another.
45
1 Pa( pascal )=
94 dB SPL
46
Microphone Sensitivity is measured in?
decibels of voltage per pascal of | sound pressure. For example, a microphone may have a specification that reads, -54.5 dBV/PA (1.85 mV)
47
PAG
Potential Acoustic Gain. Gain before feedback is frequently referred to as potential acoustic gain (PAG).
48
NAG
Needed Acoustic Gain
49
typical speech reinforcement system SPL
65-70 dB SPL
50
signal-to-noise (S/N) ratio for voice reinforcement?
25 dB
51
electronic S/N ratio
This is the electronic S/N ratio of the electronic components. The signal level in the system should be at least 60 dB above the combined noise inherent in all the electronics in the signal path. Should be 60 dB
52
SIN Ratio
Signal to noise ratio is the ratio , measured in decibels, between the audio or video signal, and the noise accompanying the signal. The higher the S/N ratio, the better the quality of the sound or picture.
53
Stable Audio
Stability applies only to systems using microphones that are being reinforced in that same room. Can you turn the loudspeakers' volume up loud enough for the signal to be heard without causing feedback?
54
Speech loudness level
Average speech levels should be in the 65 to 70 dB range if persons with normal hearing are to understand it without effort. typically, a 15 dB speech-to-noise ratio may suffice in sports activities were there is considerable spectator noise.
55
Normal face-to-face speech communication SPL
is about 60 to 65 dB SPL,but most speech reinforcement systems operate between 70 - 75 dB SPL. If the level of amplified speech is increased beyond that range to about 85 to 90 dB SPL, overall intelligibility won't increase much, and most listeners will complain of excessive levels.
56
direct to reflected ratio
It takes the level of the direct sound - all the sound directly from the source to the listener - and compares it to the level of the reflected sound - all the sound that has arrived to the listener by an indirect pathway and determines the intelligibility of the system.
57
In order to work properly, a sound system must do three things:
1. It must be loud enough 2. It must be intelligible 3. It must remain stable
58
EAD
Equivalent Acoustic Distance, is the farthest distance one can go from the source without the need for sound amplification or reinforcement to maintain good speech intelligibility . It is a design parameter dependent on the level of the presenter and the noise level in the room .
59
NOM
Number of Open Microphones - Each time the number of open microphones is doubled, there is a 3 dB loss before feedback. In speech applications, microphones assigned to an auto mix bus in an automatic microphone mixer will have an equivalent open microphone of 1 .
60
FSM
Feedback Stability Margin - FSM refers to how close the system is to actual feedback. Any system on the edge of feedback will produce a ringing behavior prior to actual feedback. The FSM in a carefully equalized system is typically 6 dB.
CTS-D
flashcards
Decks in class (12)
# Cards
Brainscape helps you reach your goals faster, through stronger study habits.
© 2026 Bold Learning Solutions. Terms and Conditions