What degree is the tail rotor canted
20 degree
What servos does the pilot assist module drop down to 1,000 PSI
Pitch and roll trim servos
What is the size of the cabin door
54 X 44 inches
When bleeding the hydraulic pumps back to what point do you bleed it back
3/8 inch forward edge of green
What dos CAAS stand for
Common avionics architecture system
Type of Engine
T700-GE-401C
On V1/V2 what is the letter for the preset for AM?
V- VHf-AM
Hoist failure
1.Advise pilot
2. Check Back up pump on
3. Check rescue hoist to all
Caution : full up limit switch is inactive in back up
4. Going to back up control
5. Complete hoist or abort as required
After hoist is complete troubleshoot as required
6. Back up control push to off
7. Rescue hoist circuit breaks check/reset
Rescue hoist power CB R2 #4
Rescue hoist CONTRL CB R6 #2
Rescue house CONTRL CB R6 #9
8. Check operation of alternate control (pendant or grip)
9. Disconnect pendant recheck grip
Runaway Hoist
- Advise pilot
- Going to back up control - push to on
If runaway continues - Set back up pump - off
- Abort hoist and make on scene repairs, abort the mission or take other actions as appropriate
Fouled cable
- Immediately pay out cable
- Advise pilot
If injury or damage is imminent: - “SHEAR SHEAR SHEAR”
- Emer rel- press (P,CP)
- Hoist SHEAR-SHEAR(FM)
If injury or damage is not imminent - Maintain position
- Attempt to have flight mechanic and boat personnel free cable or rescue device.
If unable to free device from deck: - Cut cable with cable cutters
- Abort mission or rig quick splice and continue hoist
ICS Failure
- Perform ICS Check : visually inspect hoist pendant ICS switch and visually Inspect chord. If in a safe position to do so, retrieve device.
- Perform ICS Check : check PTT and chord
- Slowly move aircraft to establish visual reference with hoisting area
- Pay out slack as necessary.
- Troubleshoot ICS malfunction
If ICS malfunction has been corrected, proceed with normal hoist procedures.
If ICS malfunction has not been corrected - Position aircraft to recover rescue device as per rescue briefing.
- Signal pilot to reestablish visual reference with hoisting area by pointing to the left side of the aircraft. Rescue device may or may not have been recovered.
- Observe signal, pass to pilot
- Slowly move aircraft to establish visual reference with hoisting area.
If rescue device has been recovered - Complete hoist of rescue device
If rescue device has not been recovered - Make on scene repairs, abort mission, or take other actions as appropriate.
Hoist hydraulic overheat
- As soon as practical, cease operation of rescue hoist until light goes out
- Check rescue hoist circuit breakers.
Rescue hoist power(CAB R2 #2)
Rescue hoist CONT (CAB R6#2)
Rescue hoist CONT (CAB R6#9)
ERD max load
300lbs
ERD usable line
And total
140 usable
155 total
Hoist hydraulic overheat light will illuminate at what temperature
115c
When recovering a survivor with the quick strop the crotch strap shall be utilized when ________
Survivor is unconscious
When the main rotor head is rotating over ______ centrifugal force pulls the antiflapping assemblies outward
35%
At what temperature range should a hydraulic pump reservoir be replace due to overheating
270-275
When the main rotor is rotating between ________, centrifugal force pulls out the droop stops
55-60
The SLDMB may be deployed from a range of ____ft at a airspeed range of _______ KIAS
100-10000 ft 45-120kias
Span of Stabilator
14ft 4 in
Main rotor diameter
53ft 8in
Tail rotor diameter
11 feet
Length of aircraft
Height of aircraft to top of tail rotor
64ft 10in
16ft 9in
